The 10 Best firmware for ender 3 pro Comparison & Top Picks

Our team of experts has spent considerable time researching and analyzing the firmware for ender 3 pro. So, if you want detailed insights, make sure you read the entire article carefully in the end.
We always take the extra step when listing and reviewing products, so that our visitors are comes in contact with the best and most reliable firmware for ender 3 pro. After hours of analysis and research, we conclude that Creality 4.3″ Touch Screen with F1RST LAYER FIRMWARE for Ender 3/3 Pro / 3 V2 / 3 Max / 5 / for 4.2.7 Control Board ONLY with Upgraded Open-Source Firmware – Improved UI and Faster Operation may be the best one for your needs. But, if you are still looking for something cheaper and more reliable, you can go to Creality Ender 3 / Pro / V2 Plug and Play LCD Color Touch Screen + v3.1 BL Touch + 4.2.7 32Bit Silent Board + Runout Sensor + F1RST LAYER Open-Source Community Firmware – E3 Max / 5 Compatible .
The table below provides a quick overview of the best firmware for ender 3 pro. You can check out the design before reading a full review. Also, features that make each product stand out from the crowd are highlighted in order to save your valuable time.

Our comparative list available as well as our recommendations.

To help you make a pleasure buying decision, we have prepared the following section with some key features of each of these firmware for ender 3 pro. Take a look at the products below and pick the best one that fulfills your needs:

Creality 4.3" Touch Screen with F1RST LAYER FIRMWARE for Ender 3/3 Pro / 3 V2 / 3 Max / 5 / for 4.2.7 Control Board ONLY with Upgraded Open-Source Firmware - Improved UI and Faster Operation

$42.99
as of November 24, 2022 7:06 am

Features

  • This Ender 3 touch screen is fully open source thanks to a partnership between First Layer with Insanity Automation. This screen comes from the factory flashed with our custom firmware for more features than ever. Now supports dual gear extruder, filament sensor, mesh bed leveling features, change filament function, screen brightness and standby timer, built in PID tuning, silent touch screen mode, direct drive extruders. This product is an Ender 3 display screen ONLY, no control board included.
  • A custom DWIN_SET makes this the first open source Ender series touch screen on the market to be compatible with any Ender 3 / V2 / Pro / 5 on the market. Along with more added features than any other touch screen available today, this is THE best version of this product available on Amazon right now. With this new open source build, not only have critical bugs preventing users from even turning on their printers been fixed, but more printers than ever can use this touch screen
  • Compatible with Ender Series printers as direct swap for your older stock screen IF you have a 4.2.7 32-bit silent control board. This screen does with 4.2.2 boards however you will have to flash Crealitys firmware onto both the board and the screen. Crealitys firmware is not compatible with Ender 3 Max / Ender 5 and Ender 5 Pro.
  • Realistically Creality should have updated their Ender Series screens years ago but haven’t. Their firmware catalogue is also outdated and basic, ours is not. We invite you to browse are extensive firmware catalogue on our google drive and view videos on YouTube regarding this screen and our firmware. This upgrade is the equivalent of upgrading your phone from a Nokia 3310 to an iPhone.
  • First Layer have partnered with Insanity Automation to hack this touch screen and unlock its full open source potential! This kit is completely Plug-and-Play and enhance your Ender 3 with previously unavailable features, while also allowing for the BL Touch upgrade in the future if you want to install it. Please note this Touch screen is flashed with a custom DWIN_SET folder developed by Insanity Automation for First Layer. Stock Creality firmware for the 427 board WILL NOT work with this screen

Creality Ender 3 / Pro / V2 Plug and Play LCD Color Touch Screen + v3.1 BL Touch + 4.2.7 32Bit Silent Board + Runout Sensor + F1RST LAYER Open-Source Community Firmware - E3 Max / 5 Compatible

$129.99
$119.99
as of November 24, 2022 7:06 am

Features

  • This Ender 3 touch screen is now FULLY open source thanks to a partnership between First Layer and Insanity Automation. The ONLY open source AND Plug-And-Play Ender touch screen on Amazon, flashed at the Creality factory with our custom firmware for more features than ever. NEWLY SUPPORTED: dual gear extruder, filament sensor, mesh bed leveling features, change filament function, screen brightness and standby timer, built in PID tuning, silent touch screen mode, direct drive extruders and more!
  • A custom DWIN_SET makes this the first open source Ender series touch screen on the market to be compatible with any Ender 3 / V2 / Pro / 5 (Ender 5 must update board firmware). Along with more added features than any other touch screen available, this is THE best version of this product available on Amazon right now. With this new open source build, not only have critical bugs preventing users from even turning on their printers been fixed, but more printers than ever can use this touch screen.
  • This is the newest version of Creality's 4.2.7 32 Bit silent control board with authentic TMC2225 Trinamic stepper drivers which greatly reduces the sound of the stepper motors during use. The 4.2.7 board comes flashed with our custom Marlin firmware that works with all Ender 3 series printers. This entire hardware swap will take less than 1 hour and quickly turns your stock Ender into a touch operated printer in just one upgrade as well as adding dozens of features over stock Creality firmware!
  • The BL Touch is an incredibly accurate and reliable auto-mesh bed leveling sensor that probes individual spots for differences in Z height on any print surface such as glass, aluminum, PEI, BuildTak with incredible accuracy to 0.005mm. This is especially great for users with small imperfections or warping in their print surface as manual leveling will never be able to account for these variables. Custom firmware even speeds up this process to further save time while still maintaining accuracy
  • First Layer have partnered with Insanity Automation to hack this touch screen and unlock its full open-source potential! Enhance your Ender 3 / Pro/ V2/ Max/ 5 with previously unavailable features. Please note this Touch screen is flashed with a custom DWIN_SET folder developed by Insanity Automation for First Layer. Please contact F1rst Layer directly for any questions or technical support. A filament runout sensor, 24V silent fan and metal carrying handle are also included in this kit.

Official Creality New Upgrade Motherboard Silent Mainboard V4.2.7 for Ender 3 Pro Customized and Non-Standard Matching,Ender 3 Pro Silent Motherboard

$46.99
2 used from $36.40
Free shipping
as of November 24, 2022 7:06 am

Features

  • Creality new release silent motherboard V4.2.7 to 32bit, compatible with Ender 3 Pro.
  • Super quiet by TMC2225 driver , bootloader installed,copy the firmware file to a formated SD card with no other files in it. Turn off the printer and unplug the power cord. Insert the SD card & power cord, and turn on the printer. Wait 10s to complete the firmware updating process., easier to flash the firmware.
  • Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve Heating Problem.
  • Firmware comes pre- installed, pre-configured for the Ender 3 Pro, makes it totally plug & play.
  • This silent motherboard preinstalls the Ender-3 Pro firmware. If you want to install it in your Ender 3/Ender 3 v2/Ender-5, need to flash the Ender 3/Ender 3 v2/Ender-5 firmware.

Creality Ender 3 New Upgrade Motherboard Silent Mainboard V4.2.7 with TMC2208 Driver for Ender 3/ Ender 3 Pro/Ender 5 /CR-10(Customized and Non-Standard Matching)

$48.99
$37.99
5 used from $30.05
Free shipping
as of November 24, 2022 7:06 am

Features

  • Super Quiet. Compatible with Creality Ender 3, Ender 3 Pro, Ender 3 V2, Ender 5 3D printer. PLEASE NOTICE: It only plug and play for Ender-3 & Ender 3 Pro. If you want to install it on Ender-5, please flash Ender-5 firmware. You can download firmware from official website.
  • Driver - TMC2225 driver & Creality V0.0.6 firmware ( based on Marlin 2.0.1) for V4.2.7 board. Bootloader has been preinstalled.
  • Update Firmware - Please copy the firmware file to a formated SD card with no other files in it. Turn off the printer and unplug the power cord. Insert the SD card & power cord, and turn on the printer. Wait 10s to complete the firmware updating process.
  • Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem.
  • Any issues or questions about our product please feel free to contact us at any time. We have professional technical Team to provide technical supports for you as soon as we can.

Official Creality 3D Ender 3 Pro Silent Motherboard V4.2.7 Upgrade Mute Mainboard with TMC2225 Driver for Ender 3/Ender 3 V2/Ender 3 Pro/Ender 5

$39.99
3 used from $27.99
Free shipping
as of November 24, 2022 7:06 am

Features

  • New Upgraded V4.2.7 Motherboard Compatible with Ender 3, Ender 3 Pro, Ender 3 V2, Ender 5. NOTE: It only preinstalls the Ender 3 Pro firmware, if you want to install it in your Ender 3, Ender 5 or Ender 3 V2, need to flash the Ender 3 / Ender-5/Ender 3 V2 firmware.If you need the firmware, please contact us freely. Ender-3 / Ender-3 Pro/ Ender 5 use the same mainboard but different firmware, please select the type you need. For Ender 3 Pro, You just plug and install them in and start operate!
  • New Upgrades: The microcontroller is upgraded from 8-bit to 32-bit, the running speed is obviously accelerated; the noise is lower and the precision is higher. Increase material breakage detection and automatic leveling function.
  • Driver: TMC2208 driver & Marlin 1.1.9 for V1.1.5 mainboard while TMC2225 driver & Marlin 2.0.1 for V4.2.7 mainboard. Bootloader preinstalled on both version boards.
  • Thermal runaway protection is enabled. The Board is Optimized by Circuit, effectively solve the Heating Problem. Eeay to Operate: With USB Port,can be Worked With E/Z/Y/X Axis Motor. Voltage: Support 24V input voltage.
  • Update Firmware: If the board you received is V1.1.5 please flash firmware with ISP cable. If the board you received is V4.2.7, please copy the firmware file to a formated SD card with no other files in it. Turn off the printer and unplug the power cord. Insert the SD card & power cord, and turn on the printer. Wait 10s to complete the firmware updating process.

Creality V4.2.7 Upgrade Mute Silent Mainboard for Ender 3 Pro Customized Silent Board, Ender 3 Pro Silent Mother Board

$45.99
1 used from $43.27
Free shipping
as of November 24, 2022 7:06 am

Features

  • Suitable for Ender 3 Pro; Silent function Customized and Non-standard matching.
  • The TMC2225 driver is super quiet.
  • Firmware comes pre-installed, and pre-configured for the Ender 3 Pro, making it totally plug & play.
  • It can work with Ender 3/Ender 3 v2/Ender-5 3D Printer. PLEASE NOTE: You need to flash firmware for your printer if you install this board on those printers. You can download firmware from the official website or contact us for related firmware.
  • If you have any unsolvable problems during installation and use, please feel free to contact us, our after-sales technical team will provide you with detailed solutions within 24 hours.

Creality BLTouch V3.1 Auto Bed Leveling Sensor Kit for Creality Ender 3 V2/Ender 3/Ender 3 Pro/Ender 3 Max/Ender 5/Pro with 32 Bit V4.2.2/V4.2.7 Mainboard 3D Printer

$47.99
$42.99
1 used from $36.09
Free shipping
as of November 24, 2022 7:06 am

Features

  • 【Widely Application】: Creality BL Touch works for Creality Ender3 v2/Ender3/Ender3 Pro/Ender 3 Max/Ender5/Ender5 Pro with 32 bit v 4.2.2/4.2.7 mainboard.(Require 3d printer with 32 bit V4.2.2 or V4.2.7 motherboard )
  • 【Easy Firmware Installation】: Simply download the BLTouch firmware(Note:words "without adapter"firmware) from the Creality Official Website and save the file to your printer’s memory card. Insert the card in to your printer. Turn on the printer and wait a few seconds for the firmware to install.
  • 【Easy to Install and Use】3 kinds of Different mounting brackets allows for installation on several of our printers.
  • 【High-precision】Enhanced leveling with precision of +/- 0.005mm. This allows for easy leveling with pinpoint accuracy.
  • 【Genuine High Quality Set】Our package was included 1 set of auto bed Leveling Kit and an another replacement probe. Simple, smart and easy to install. If you have unsolvable problems during installation and use, please feel free to contact us, our after-sales technical team will provide you with detailed solutions within 24 hours.

BIGTREETECH Upgraded SKR Mini E3 V3.0 Silent Board 32bit Mainboard Integrated with TMC2209 Stepper Driver Support Marlin/Klipper Firmware Compatible with Ender V2 Ender 3 Pro/5 3D Printers

$44.99
as of November 24, 2022 7:06 am

Features

  • 【High Compatibility】SKR MINI E3 V3.0 Control board compatible with Ender V2 Ender 3/ende 3 pro/ender 5/ender 5 pro/CR-10 3D printer, the firmware is pre-install well before we ship out, you can select the firmware base on your needs.
  • 【Multiple Functions】It Supports BLTouch, RGB lights, blocking detection, shutdown function. What ’s more, it also supports TFT35 E3 V3.0/TFT35 V3.0/TFT28 V3.0 touch screen as well as original 12864 LCD of Ender 3 printer.
  • 【Superior Heat Dissipation Performance】New Upgraded SKR MINI E3 V3.0 main board is equipped with a large Aluminum heat sink of stepper motor driver instead of pieces small heat sink, this design is able to increase the heat dissipation performance of the motherboard by 20% which greatly strengthen the heat dissipation capacity of the driver totally.
  • 【Firmware Update】Compatible with Marlin and Klipper firmware. Firstly download firmware on GitHub website of SKR MINI E3 V3.0 motherboard,copy and save it to SD card , firmware must bed reserved, then re-plug the SD card and wait to 10s. The n firmware has been successfully updated. Note: Our control board come without SD card.
  • 【TMC2209 Drivers】SKR MINI E3 V3.0 mainboard adopts ultra silent TMC2209 stepper motor driver, it generates lower heat and it has a large-area cooling position to lower the temperature when driver working. Meanwhile, it adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque.

Creality 3D 32bits New Version Upgrade Silent Mainboard Motherboard with TMC2225 Stepper Motor Driver V4.2.7 Version for Ender 3/Ender 3 pro/Ender 3X

$45.59
2 new from $45.59
Free shipping
as of November 24, 2022 7:06 am

Features

  • New Version: This is the newest Silent Controller board for Creality 3D printers
  • Driver:TMC2225 drivers and Boothloader installed the firmware can be modified by ARDUNO with USB cable.
  • Thermal runaway protection is enabled.The Board is Optimized by Circuit ,effectively solve the Heating Problem.
  • Easy to Operate:With USB Port,can be Worked with E/Z/Y/X Axis Motor Fimware 1.1.8 comes pre-installed on this board.Suitable for Ender-3 /Ender3 Pro.

Creality 3D Original Ender 3 Z-Axis Upgrade 2040 Profiles Kit with Two 50CM Aluminum Extrusions and Lead Screw Enlarging 10CM Printing Space for Ender 3/Ender 3 Pro/Ender 3 V2

$25.99
as of November 24, 2022 7:06 am

Features

  • [Super Aluminum Material ] This Upgraded Ender 3 Z-axis 2040 Profiles made by high aluminum material,high wear-resistance which make it possible to bear high load.The cut are so flat and smooth with clear lines are durable and stable.
  • [Enlarge Printing Size] After you install this Z-axis profiles kit, the print height will be higher 100mm then previous print size. Achieved one printer with two printing size, if you want to print higher items, you can just replace this Z-axis profiles kit and use it. Note: need upgrade the firmware, please download the firmware file in below link. https://u.pcloud.link/publink/show?code=XZ8eb4XZbvTQYG1BLfHGWclaBOlMu0kPwaoy
  • [Precise&Accurate] P3-P7 linear rails, precise and smooth, the repeated positioning precision reached up to 0.1mm, The capacity of bearing high load supports high-speed and strong motion.
  • [Compatibility] This Z-axis 2040 profiles kit is suit to Ender3 series, such as Ender3/Ender3S/Ender3 Pro. The profiles size is L500mm, the linear rail size is L450mm.
  • [What You Get] The package include :2040 Profiles x2+Linear rail x1+T-nut x1+Hexagon screwdriver x2; If you have any problem, please click "ask a question" to contact us, we are servicing with 24H.

This unbiased article currently lists a few of the best firmware for ender 3 pro in the market and also includes in-depth details of every item to help you make the right decision. If you do not find your own choice, check these Official Creality New Upgrade Motherboard Silent Mainboard V4.2.7 for Ender 3 Pro Customized and Non-Standard Matching,Ender 3 Pro Silent Motherboard , it is the best selling item in the market. If you think that the information provided here is confusing, wrong or actually removed from the actual information, please do not hesitate to contact us. We’ll always be there for you.